Jump to calculator
Advertisement

Deck Calculator: Boards, Joists, Footings & Cost

Enter your deck size to get a material list for decking, joists, beams, posts, footings, concrete, and screws. It counts materials; it does not size the structure.

Deck Calculator

Quick tools

Reopen recent results anytime.

Scenario presets

Pick a deck to start from

Load a common deck size, then adjust any input.

0 to 1/4 in. Default 1/8 in (0.125).

Composite makers often require 12 to 16 in.

Label only. Allowable span is not calculated here.

Posts, Footings and Waste

Use your local frost depth and permit requirements.

Typical: 10%, more for diagonal boards.

Optional Prices

Quick checks

•

Measure the deck length along the house and the width as joist span

Quick checks

•

Match joist spacing to your decking, since composite often needs 12-16 in

Quick checks

•

Confirm joist, beam, and footing sizes with IRC R507, AWC DCA 6, or your building department

Deck design choices

Settle the deck type and board choice before you count lumber

Attached versus freestanding, decking material, and joist spacing each change the material list.

Attached to the house (ledger)

One beam and one row of posts, with a ledger board bolted to the house.

  • •Fewer posts and footings
  • •Needs a ledger board, flashing, and joist hangers
  • •Ledger attachment is a code-critical detail
Ledger connections are a common failure point. Follow local code and inspection requirements.

Freestanding

Two beams and two rows of posts, with no structural connection to the house.

  • •Doubles posts and footings versus attached
  • •No ledger board or house flashing
  • •Often used when the wall cannot take a ledger
Freestanding decks may still need bracing and a permit. Check with your building department.

Wood versus composite boards

Both use about a 5.5 in face, but spacing rules and cost differ.

  • •Composite often needs 12-16 in joist spacing
  • •Follow the maker gap guidance for your board
  • •Higher cost per board, lower upkeep
Always check the decking manufacturer instructions for maximum joist spacing.

What this calculator does not decide

It counts materials. Joist, beam, and footing sizes depend on span, load, species, and local code, so confirm them with IRC R507, AWC DCA 6, or your building department.

Fast planning rules

Start with the deck rules that change the lumber order

Check board coverage, joist spacing, and code limits before you buy.

Deck boards per square foot

A 5.5 in board with a 1/8 in gap covers 5.625 in of width, so every 100 sq ft needs about 213 linear ft of decking before waste.

Narrower boards need more pieces: a 2×4 deck takes about 331 linear ft per 100 sq ft.

Joist spacing

Joists at 16 in on center are the common default. Composite decking often requires 12 to 16 in, and 24 in is only for boards rated for it.

Check the decking maker instructions, then check the span tables for the joist size you plan to use.

What this tool does not size

It counts materials for the layout you enter. It does not check allowable joist, beam, or footing sizes.

Use IRC R507, AWC DCA 6, or your building department for sizes and permits.

How deck materials are calculated

The calculator treats the deck as a rectangle. The length runs along the house, which is also the direction of the beam and ledger. The width is how far the deck projects, which is the joist length. Deck boards run along the length, so they cross the joists at right angles.

  • Board rows = width in inches ÷ (board face + gap), rounded up
  • Boards per row = deck length ÷ board length, rounded up
  • Total boards = rows × boards per row × (1 + waste), rounded up
  • Joists = deck length in inches ÷ spacing, rounded down, plus 1
  • Posts per beam = beam length ÷ post spacing, rounded up, plus 1. One beam if attached, two if freestanding
  • Concrete = π × radius² × depth per footing, divided by the bag yield (0.45 cu ft for 60 lb, 0.60 cu ft for 80 lb), rounded up
  • Screws = rows × joists × 2, plus waste. Boxes assume about 350 screws per 5 lb box, which varies by brand

Worked example: 16 ft × 12 ft attached deck

Inputs: 5/4×6 wood boards (5.5 in face), 1/8 in gap, 16 ft boards, joists 16 in on center, ledger-attached, posts 8 ft apart, 12 in × 36 in footings, 80 lb bags, 10% waste. These are the calculator's default values, and the numbers below come from the same function it uses.

Item Calculation
Deck area 16 ft × 12 ft = 192.0 sq ft
Board rows 12 ft × 12 = 144 in ÷ (5.5 in + 0.125 in) = 25.6, rounded up to 26
Boards 26 rows × 1 board (16 ft) = 26; × 1.10 waste = 29 after rounding up
Joists 16 ft × 12 ÷ 16 in = 12, plus 1 = 13 joists, each 12 ft
Rim board and ledger 1 outer rim board and 1 ledger board, each 16 ft
Beam and posts 1 beam, 16 ft ÷ 8 ft = 2, plus 1 = 3 posts and footings
Concrete 3 × (π × 0.5² × 3 ft = 2.36 cu ft) = 7.1 cu ft ÷ 0.60 = 12 bags of 80 lb
Screws 26 × 13 × 2 = 676; × 1.10 = 744, about 3 boxes
Joist hangers 13, one per joist on the ledger side

Deck board coverage per 100 sq ft

Using the same row logic with a 1/8 in gap and no waste. Wider boards cover more area per piece.

Board Linear ft per 100 sq ft 16 ft boards per 100 sq ft
2×4 (3.5 in face) 331 21
5/4×6, 2×6, or composite (5.5 in face) 213 14

Real decks round up by row, so a small deck uses a higher share of waste than these per-100 sq ft figures suggest.

Joist spacing notes

Closer spacing adds joists and hangers but gives stiffer decking. For the 16 ft example, 12 in on center needs 17 joists, 16 in needs 13, and 24 in needs 9. Many decking makers set their own maximum spacing, and composite boards often require 12 to 16 in, or tighter for diagonal layouts. Read the instructions for your board. The joist size you can use at a given spacing and span comes from span tables, not from this calculator.

Before you build

Not structural engineering advice. This page gives material estimates for planning only. Rules differ by jurisdiction.

  • Permit: Most jurisdictions require a permit for an attached deck or one above a set height. Ask your building department before you order.
  • Span tables: IRC R507 and the AWC guide DCA 6 (Prescriptive Residential Wood Deck Construction Guide) cover joist, beam, post, and footing sizes. Use them or your local amendments to confirm the sizes you enter here.
  • Ledger: Attach it with approved fasteners and flash it so water does not get behind it. Ledger connections are a common point of deck failure.
  • Frost depth: Footings generally need to reach below the local frost line. The 36 in default is only a starting number.
  • Utilities: Call 811 before you dig footing holes.

How we checked this page

Written by: TheSiteMath Editorial Team
Reviewed by: TheSiteMath editors (formula, source, and update review)
Last reviewed: 2026-03-20
Publisher: TheSiteMath
Scope: U.S. construction material estimating, calculator workflows, and project planning guidance for contractors and homeowners.
What we checked:
  • • Formulas checked against trade and source material
  • • Verified against: Current U.S. material pricing benchmarks, TheSiteMath calculator and content cross-check workflow, Final local code, permit, and supplier verification before purchase
  • • Price ranges used for planning, not as fixed quotes
  • • Examples checked in the live calculator
Methodology:
  • • Example quantities and explanations on this page are cross-checked against the matching live calculator on TheSiteMath.
  • • This deck content is scoped for U.S. planning and estimating workflows, not for stamped engineering or permit approval.
  • • We review formulas, material assumptions, and practical steps against category-appropriate references before publishing updates.
  • • We refresh pages when calculator logic, supplier assumptions, or pricing guidance materially changes.
  • • Readers should confirm final dimensions, structural requirements, and local code obligations with qualified local professionals.
Editorial standards: We review pages before publication and update them when formulas or pricing need a fix. If you spot an issue, please contact us .

For our review process, corrections policy, and monetization disclosure, see the Editorial Standards page.

Deck FAQ

Deck material questions before you order lumber

These questions focus on board count, joist spacing, posts and footings, fasteners, and cost so the deck material list is complete. They are planning answers, not structural design.

How many deck boards do I need for a 12×16 deck?

A 16 ft by 12 ft deck is 192 sq ft. With 5.5 in boards and a 1/8 in gap you need 26 rows across the 12 ft width. With 16 ft boards that is 1 board per row, so 26 boards, or 29 with 10% waste. With 12 ft boards you would need 2 per row and 58 boards with waste.

How many joists do I need for a deck?

Joists = deck length in inches ÷ spacing, rounded down, plus 1. For a 16 ft deck at 16 in on center that is 13. At 12 in it is 17, and at 24 in it is 9. The calculator also lists the rim (band) boards along the deck length: one on the outer edge plus a ledger board for an attached deck, or two rim boards for a freestanding deck. Joist size and allowable span are not calculated, so check IRC R507, AWC DCA 6, or local code.

How many posts and footings does a deck need?

Posts per beam = beam length ÷ post spacing, rounded up, plus 1. For a 16 ft beam with posts 8 ft apart that is 3. A ledger-attached deck has one beam, so 3 posts and 3 footings. A freestanding deck has two beams, so 6 posts and 6 footings. Post spacing and footing size must match your beam size, loads, and local code.

How much concrete do deck footings need?

Each footing is a cylinder: π × radius² × depth. A 12 in diameter by 36 in deep hole holds about 2.36 cu ft. For the default attached deck, 3 footings need 7.1 cu ft, or 12 bags of 80 lb concrete (0.60 cu ft each) or 16 bags of 60 lb (0.45 cu ft each). The freestanding version needs 24 bags of 80 lb. Your footing depth must reach below the local frost line and meet code.

How many deck screws do I need?

The calculator assumes 2 screws per board at each joist. For the default deck that is 26 rows × 13 joists × 2 = 676 screws, or 744 with 10% waste. At roughly 350 screws per 5 lb box, that is about 3 boxes. Box counts vary by screw size and brand, and hidden-fastener systems use clips instead, so check the box label.

Does this calculator include stairs, railing, or labor?

No. It covers a rectangular deck: decking, joists, rim joists, ledger, beams, posts, footings, concrete, screws, and joist hangers. Stairs, railing, flashing, post bases, carriage bolts, lighting, permits, and labor are not included, and cost totals include only the prices you enter.

Advertisement

Projects / Pro

Loading plan details...